<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Capturing Miter Saw Dust

      Ideas and suggestions for dust control at the chop saw. September 23, 2013

Does anybody know of a good way to capture sawdust from a chop saw? I would like to have something that focuses the dust so it can be more easily picked up with a shop vac or dust collector.

Forum Responses
(Cabinetmaking Forum)
From contributor K:
Hook your shop vac to the exhaust of the saw... If needed, get a transition piece.

From contributor I:
A hose alone will not do it. You will need a hood or enclosure to get the rest.

From contributor K:
I am assuming this is for a job site, not at the shop. At the shop, hood enclosure works.

From contributor M:
Richelieu sells a complete hood or tent which captures almost all of the debris and funnels it into a 5 gallon pail.

From contributor E:
I think Fastcap sells a hood setup. If you use a shop vac, there is a plug in unit that both the vac and saw plug into. When you turn the saw on, the vac comes on.

From contributor G

Click to View Member Profile Member Contact Info

I have a Dewalt slider and I bought a Downdrafter from a fellow who wasn't satisfied with it. I hooked it up to my dust collector with a 5" hose instead of the 4" as the original owner did and I'd say that now it captures 95% of the dust. It's easy to use although I have to tie it to the saw with some bungee cords.

From contributor G

Click to View Member Profile Member Contact Info

I'm surprised no one has mentioned the Festool Kapex and a Festool dust extractor? Is that combination not as good as they say it is?

From contributor J:
We have the Festool setup and love it. It is the best available without going to a large, unsightly hood system. I would estimate it catches 75% of the dust.

From contributor E:
I've been a cabinetmaker since 1970. I finally decided to clean up my mitre box area (that didn't take too long - 1970-2013!). I got a Ridgid 5hp shop vac and one of those automatic switches. I hooked it up with transitions to the dust port on my DeWalt 12'' slider. It picked up about 20% of the dust (what a crappy design by DeWalt).

What I came up with is a half circle back stop made with bending panel and some plywood with a 4'' collector port in the back center with a small diameter hose going to the hood collector of the saw. Possibly a few smaller diameter holes in the back stop spread out would be better.

I had the Fastcap hood for installations to keep the site clean, until we were in NYC working on a penthouse (working outside on the roof). A brisk wind came up and carried the hood about 20 ft into the air and it got destroyed when it hit the ground.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article