<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Color Standards When Finishing

      Use a color standard or guide panel to acheive consistent results

by WOODWEB's Finishing Team:
John Buries and Bob Niemeyer

Q. Everything is going fine while I'm staining a set of 30 cabinet doors. I spray the clears on and end up with the makings of a beautiful kitchen. But during installation, I discover that some doors are lighter in color than others.

I prepared all these doors on the same day with the same can of stain. What happened?

A. John Buries responds: Here are some possibilities:

Light color - While sanding wood, sand paper wears out. This causes the wood to be slick and prevents deep stain penetration.

Dark color - The afternoon gets hotter, causing stain to dry too fast.

Color all over the place - The stain is not agitated continuously, or more than one person is staining.

Veneers and solid wood can take stain differently.

A lot could be causing the problem. By using a color standard or guide panel, however, the necessary adjustments can be made as you go to keep a consistent color.

A guide panel is easy to make: properly sand and stain to the desired shade a scrap piece of wood from the batch being used. Finish it with the correct clear coats, label and date it. Masking tape can be used to cover each step along the way, which creates a sophisticated step panel that shows the color of the original wood and how it should look as you progress.

Remember: The best time to judge color is directly after wiping off the substrate, while the stain still has that wet look. Mineral spirits, or a solvent that won't attack the clear finish, can be applied to the color standard panel to eliminate any gloss differences.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Finishing: General Wood Finishing

  • KnowledgeBase: Finishing: High Speed Production

  • KnowledgeBase: Finishing: Refinishing

  • KnowledgeBase: Knowledge Base

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article