<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Doubling Up Compressors or Fans

      When you link two fans or compressors together, what's the effect on pressure and airflow? January 18, 2007

Would two 15 scfm at 90 psi compressors equal 30 scfm at 90 psi? Or is there more to it than that? Further, how would two identical dust collectors perform wired together? I do have two Dbl bag collectors that are rated at about 2300 cfm and 16" static. I'm sure that 4600cfm and 32" is out of the question, but what would be expected by hooking both up to my widebelt? It isnít enough, but if the math works out I'd rather implement a third dust collector, rather than buying a single new, very expensive (large) dust collector.

Forum Responses
(Architectural Woodworking Forum)
From contributor J:
If you've got the room, a dedicated collector close to the machine seems like a simple solution.

From contributor L:
Yes on the 2 - 15 cfm to 30. No on the 2300x 16 to 4600x32. Your static pressure would not increase. 2300x16 should be enough for most widebelts. The usual catch with wide belts is they fill the porosity of the bags with the fine dust reducing the airflow. Solution: more bag area, different fabric.

As a side note I replaced two 38 CFM recips with one 25hp x 105cfm screw (both at 90psi) and am still short on air sometimes, everything down stream is rated larger than 105cfm, very disappointing.

From contributor W:
For the simple case of 2 machines that are identical, if ran in parallel, the flow-rates add but the pressure does not change. If ran in series, the pressures add and the flow-rates do not change. The two 2300 cfm at 16" collectors, if ran in parallel on the same system, would equate to 4600 cfm at 16".

From the original questioner:
Would you describe a practical installation of parallel vs. series for dust collectors? Also, what if the collectors were not identical? I bought an 80 gal 2 stage compressor that is rated at 27cfm/100psi - if I simply hooked up an additional 120 gallon tank what gains would be expected, and how is this calculated?

From contributor W:
If you needed more static pressure developed in your system, you would put the collectors in series. This might be the case if you had a really long run, or a lot of bends or whatever. If you just need more volume/velocity, you would put them in parallel. It depends on the system.
Looking at the fan curves for the two collectors (in parallel), the smaller of the two would not start making a contribution to the flow until its maximum static pressure was reached, then the two flow-rates for the fans (at each static pressure) would sum.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: General

  • KnowledgeBase: Dust Collection, Safety, Plant Management

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article