<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Drum-Style Filter Cartridges for Dust Collectors

      A discussion of pleated drum filters in dust collectors. September 29, 2009

Does anyone have any experience with the new drum style filter cartridges? They are showing up from most manufacturers as a relatively expensive upgrade on their ballpark 1 hp to 3 hp dust collectors. There is a handle on the top of the filter drum that you rotate to sweep the inside surface of the drum filter clean of dust.

Forum Responses
(Dust Collection and Safety Equipment Forum)
From contributor A:
I have not had good results with the cartridges. They are very hard to clean if fine MDF dust is involved. The rotating handle and internal flapper really does not work well. You end up dismantling the collector and blowing out the cartridge, which is very labor intensive. Better to use an oversize filter made by someone like American Filter Fabric.

From the original questioner:
Thank you. That's just the sort of feedback I was looking to get!

From contributor B:
I have had the opposite experience with the cartridge filters. I like the internal pleat flickers so much that I am retrofitting it to my 60" Oneida filter so that I never have to manually clean it again either. MDF dust is tough though, you have to clean the filters about three times as often.

From contributor C:
I bought one last year to run with my new planer and have to say I prefer it to the bags. There is definitely a noticeable difference in suction also, though I was going from a 2 micron bag which is more restricting than the stock 30 micron bags. One or two spins of the handle usually cleans it enough to restore airflow. I haven't tried blowing it out yet, which seems to be the standard method of cleaning. I think having a thin layer of dust cake on the filter is better than having it totally clean.

The one problem I noticed was on the planer. If the bag got over about 3/4 ful, the cartridge would fill up with shavings. To resolve this, I moved it over to my sander. It works much better with the finer dust, in my opinion.

If they weren't so expensive, I would put them on my new system. But the Beane bags are $110 apiece and supposedly filter down to 1 micron, so I can't justify the extra expense.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article