<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Dust-Collection System Sizing

      More examples of dust-collector math. August 29, 2006

I'm looking into a new dust collector for my shop. We usually run two to three machines at a time. I noticed that the cyclone collectors tend to have less cfm's than the bag style collectors. Do the cyclones have a comparable draw to them? I don't understand that much about cfm's or fpm's. Should I be looking for a collector with higher cfm's or static pressure or what?

Forum Responses
(Dust Collection and Safety Equipment Forum)
From contributor R:
If you plan to return the air to your building, you will definitely need a filter (perhaps a cyclone filter) to meet OSHA rules. You may need one for outside to meet EPA rules.

CFM, SP, and FPM are all related and need to be considered when sizing a filter. When you are quoted the values for a specific filter, ask about the values after a year or two of use. Some filters do not maintain their values.

Another area needing investigation is Interstitial Velocity. If this value is too high, problems will occur. Look at the FAQ section of our website, wolfeaire.com.

Static Pressure is confusing for many people but is important. A machinery list would be helpful to size what you are talking about.

From contributor B:
Single-stage dc's have lower built-in resistance than cyclones, so with the same blower, a single-stage will outdraw the cyclone. A cyclone is merely a pre-separator with a blower mounted to it. Think of it as two components built into one unit. One beneficial characteristic of a cyclone is that you will (should) pre-separate the bulk of your waste before it comes into contact with the filters.

Now, with regard to your specific requirement of three machines at a time, here's what to do. Determine how many cfm you want at each of those machines. Just as a guide, let's say you want 800 cfm at each machine. Since they are operating simultaneously, your main duct will have to be sized to allow 2400 cfm total. A decent 5hp dc should easily get you there.

The diameter of the ducting will determine velocity through the duct. You want 4000fpm velocity for ideal particle suspension. Look for a 9"-10" intake on the dc (depending on suction capability), to attach your main. From there, at the first 6" drop to a machine, you need a 10"x9"x 6" fitting. The 6" is the drop. The 9" is the continuation of your main to the next two machines.

At the next drop, use a 9"x6"x6" fitting (wye). One 6" is the drop, and the other 6" is for the continuation of your duct to the final machine. If the dc has a 9" intake, use a 9"x8"x6" wye at the first drop, followed by a 8"x6"x6" wye for the next drop, then 6" all the way to the last machine.

Remember, the sizes I've suggested are only for the example of 800 cfm per machine.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article