<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Easing the Edge of Shaker Style Doors

      A light touch is all that's called for. April 6, 2007

I have made a few shaker style doors. They look great with a reversed raised panel and have the feel that I like. Since this is the first time I've done this style of door, I'm wondering what the best way to handle the edges will be. What, if anything, do you do with the edges for the best look?

Forum Responses
(Cabinetmaking Forum)
From contributor M:
For shaker jobs we just barely sand the sharp edges off by hand. This is what I have seen on authentic shaker pieces and what every customer has wanted. The shaker style is meant to look like they built it way back then when they didn't have router bits.

From contributor T:
I use a 1/16" round over. Looks good.

From the original questioner:
Thanks. I was thinking of just breaking the edge with a sanding block. I ran some shaker style for a friend several months ago on my RBI door machine and I think he rounded his slightly, but didn't get to see the finished door.

I haven't seen a 1/16" router bit. 1/8" is my smallest. Can you even tell it's been hit with 1/16"? Since these doors are birch, I think I might feel safer with just the sanding block.

From contributor S:
The 1/16 bit really is tiny, but if your doors are flat (dead flat), it works good. I set mine so the lip just starts to cut (64th?) and then run a pad sander over to kill it. Finish sand before routing, clean base plate on router. I made a block that PSA paper sticks to with the rad built in, one swipe down and done.

From contributor P:
We use a Slick Plane for breaking edges a lot of the time. Faster than messing with a router, and no dust. It's also cheap.

From contributor M:
Also, some of the ones we do have been distressed to give the old worn look. If you take the random orbit sander and hold it at a 45, then you take the corner off and you can't hardly help to take more off the corners, which adds to the distressed look.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article