<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Edge Treatment for MDF

      Is it better to edgeband MDF cabinet doors, sand and paint them, or what? June 9, 2012

I'm doing a job with quite a bit of MDF cabinetry that will get a custom paint treatment by someone else. I usually don't do MDF cabinets and was wondering what edge treatment is best. The doors are full overlay with a square edge. I have an edgebander, but I have seen MDF cabinets on other jobs that just come out with raw edges. If you edgeband, what material do you use?

Forum Responses
(Cabinetmaking Forum)
From contributor L:
You can use maple, which has a nice closed grain, or a paper edging that will have no grain.

From contributor S:
We have done a bunch of MDF doors, both cabinet and passage doors. We never edgeband anything, as the edges paint or lacquer great. I think edgebanding would give you problems.

From contributor U:
MDF is great for cabinet doors. They take paint very well and are permanently dimensionally stable. MDF is terrible for cabinet boxes. It is unnecessarily heavy and has poor structural characteristics. We use MDF for all painted doors and edgeband birch plywood for our boxes.

From contributor W:
With raw MDF edges, it requires sanding and 2 coats of primer. We use resin saturated paper. This makes for fast painted edges.

From contributor J:
I used to use birch or maple banding, but on the last job tried the paper. Way better, in my opinion. I think it looks more professional to have the edges banded than raw.

I used MDF on a shelving unit a couple years ago. Never again! Even pre-drilling I had a lot of problems with the material splitting. Particleboard or plywood both work much better for casework. Save the MDF for just the doors.

From the original questioner:
The boxes will be white melamine. Spoke with my supplier and he suggested a polyester paint grade material. He's sending me a roll to look at. He didn't know about the resin saturated paper though. Thanks.

From contributor U:
A primer/sand-and-vacuum/primer sequence will fill most of your MDF edge grain concerns prior to painting. When we are extra concerned about the porosity of the MDF edge grain showing, we mix a glue and water solution and quickly brush it on with an acid brush. We also use a simple off the shelf wood hardener from the pigment stain company. Brush it on with a paint brush, dries in 10 minutes. The MDF sands very nicely and holds the paint well. The glue/water and the hardener are liquid so they contour to any surface.

From contributor G:
We PVC edge the boxes matched to the same color as the painted MDF doors. The painted edges often get nicked with plates and stuff and will look horrible in a year's time.

From contributor Z:
We're in the UK and use it all the time. Sure takes the hard work out of preparing MDF edges. Available in the UK too.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article