<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Finish Sanding Hand-Planed Boards -- Without Losing the Look

      A woodworker wonders how to efficiently smooth a surface enough to take finish, without ruining the hand-planed texture. February 8, 2005

I manufacture and then hand plane (distress) wood flooring. I am looking for an automated machine/sander that can help sand out the chatter in the flooring without losing the texture prior to me pre-finishing it. Any suggestions? Orbital sanders take way too long!

Forum Responses
From contributor L:
If you do actual hand planing to the floor boards, then there is no machine that you can use to sand the board without ruining or distorting the hand planing. The only way to sand it is to use a sponge with sandpaper on it and do it by hand. Yes, slow and much labor. But if you use a machine, you will ruin all that physical labor you put into it when you hand planed it. The only way I can see doing it by machine is to use a Flappy Sander, which is a bunch of sandpaper installed onto a drum and then rotated with a motor. You would need to use 150-220 grit "J" weighted paper. I have such a machine, but I use it to sand moldings. It is set up like a molding machine and you feed the moldings through it.

From the original questioner:
Thanks. I think a flap sander of sorts may work. Or perhaps a sander with nylon brushes? I have tried some flapsanders, but in order to get the chatter out from the knives, I was also creating streaks or straight lines from the sandpaper. Perhaps I need one with several heads with different grits?

From contributor L:
I use a 1/2 HP motor spinning at 1725 RPM with a gear ratio of 13:40 for a flappy speed of 560 RPM. There is a large nut and bolt that is the hookup for my variable speed Delta stock feed roller. I got the flappy drum from Wood Workers Warehouse, but they are out of business now. Make sure to rip/cut the paper on the ends so you get a paintbrush effect. 1/4" spacing between the rips is what I use. If you are doing wider boards, you can spin them around and do a second pass or get more drums. I used pillow block bearings and a gocart axle because it had the correct 1" diameter. I got most of the stuff from Northern Tools.

From contributor B:
I did a ton of this work in the late eighties for the Beverly Hills crowd; learned a few things, too. If you are using a rounded off paint scraper to plane the wood, you will get a lot of chatter, and fuzz.

Try a scrub plane. This tool has been largely forgotten since the advent of power tools. It has a curved blade and wide throat to clear a lot of shavings without jamming up. It's what was used to dress timber to size before smooth planing. Those characteristic marks seen in older timbers you are trying to recreate were probably made by this tool. You will also be pleased when you find how much faster they are to use than a paint scraper. The marks they make are a bit more distinct and hold up to sanding without washing out better as well. Try regrinding the blade's radius to suit your taste.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Finishing

  • KnowledgeBase: Finishing: General Wood Finishing

  • KnowledgeBase: Finishing: High Speed Production

  • KnowledgeBase: Finishing: Refinishing

  • KnowledgeBase: Solid Wood Machining

  • KnowledgeBase: Solid Wood Machining: General

  • KnowledgeBase: Woodworking Miscellaneous

  • KnowledgeBase: Woodworking Miscellaneous: Accessories

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article