<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Frameless Cabinet Door Dimensions and Tolerances

      Of cabinet door gaps, wiggle room, millimeters, and math. June 28, 2007

How much of a reveal do you usually leave between a pair of frameless cabinet doors? I'm using a 1.5 reveal on the sides to maintain a 3mm reveal between cabinet doors and drawer fronts. Do you deduct an extra 1mm so that the doors don't bind?

Forum Responses
(Cabinetmaking Forum)
From contributor J:
What you're doing is common. I leave 2mm for a 4mm reveal, though. The math's easier and I like that little bit of extra wiggle room.

From contributor F:
Thanks for responding. So if you had two doors to place on a cabinet 304mm wide, you would order/build two doors 150mm?

From contributor B:
I use 1.5mm reveal on sides (3mm between doors), 0mm on the bottom and 3mm on top. I have not encountered any binding with hinges 4-5mm from the edge of the door.

From contributor O:
I like contributor J's idea of 4mm between doors. As a lot of us outsource doors, the wiggle room really can make a difference. A friend of mine ran into that problem with doors he ordered that were pre-finished, and slightly oversized, and not by much.

From contributor M:
I also use 3mm between doors and drawers. AWI calls for 3.2mm (1/8") with a variation of +/- .8mm (1/32") for Premium, +/- 1.6mm (1/16") for Custom, and +/- 2.4mm (3/32") for Economy.

From contributor J:
I'd order them at 148mm to get 4mm between the split doors.

From the original questioner:
Thanks for your responses! I am asking because I just built a bunch of doors for a couple of frameless built-in floor-to-ceiling units, only to discover on installation that the doors wouldn't close properly, since I had originally designed the doors slightly oversized to be trimmed down later. Well, you can guess what happened... Anyway, I trimmed down the doors to allow for 1.5mm on each side of the doors and 1mm in between. In the future I'll make sure to size a pair of doors: (width of cabinet-4)/2 and for a single door: width of cabinet-3 to allow for the 3mm reveal.

From contributor M:
3mm between double doors is a safe distance for European hardware. Less than that, as you found, and you have issues. More than that is just too much.

From contributor B:
Standardize your products. Subtract 3mm from the width of single door cabinets and divide a double door cabinet by 2 and subtract 3mm. In that way, a 381 cabinet has the same size door as a 762 cabinet and everything in a perfect world has a 3mm gap. If you have double drawers over double doors, the drilling for the drawer front is the same as a single door/drawer cabinet. In my opinion, 4mm is too much gap. Face frame converts usually are more comfortable with a larger gap, but once you are familiar with tight tolerances, it is easier to construct.

From contributor S:
Contributors M and B, I think I got it. So you are saying that on a set of double doors, there would be a 1.5 reveal on each side of the door as well as 3 reveal between the two doors. How did you know I used to build face frame? :)

From contributor J:
I'd wager 3mm reveals came about because of old school Imperial mentality that can only understand 1/8th inch and 1/16th inch. There's nothing in the "old world" that easily translates to 2mm and 4mm. Also, in defense of 4mm reveals, I do a fair share of solid lumber fronts that move a bit, and can use that wiggle room. That little .5mm to 1mm extra space can be a life saver, the math's easier, and bottom line, in the overall scheme of things, you can't see the difference.

From contributor B:
Well... 3mm is not 1/8", just like 32mm is not 1 1/4". Close but no cigar. I can't see where subtracting 4mm is any easier math than subtracting 3mm and yes, I can see the difference. To each his own - doesn't make it right, just different.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article