<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Home Made Trailer and Crane

      Fully illustrated description of a home-built log trailer and crane. March 2, 2003

by Greg Wallace

This is the trailer and log crane that I built. The trailer is an old mobile home frame and axles, narrowed to 8' wide and heavily reinforced with iron.

The crane: The cost of a crane like this can be quite high unless you have access to some "junk" like I do. My total costs were about $1000, half of that being the Ramsey 5000# winch. The steel was purchased locally. The hydraulic cylinder, valves, winch and other stuff was purchased from Northern Tool. A few other odds and ends was purchased from the "Surplus Center" in NE.

The whole trailer. The boom is off right now and buried somewhere in the snow. I pull the trailer with a '77 Ford F250 4x4.

24" stroke hyd. cylinder will lift the boom straight up. 5000 # Ramsey winch w/100 ft cable.

The crane's frame is 6" channel iron in the center, 3" channel for braces.

20" budd wheel, axle, hub and part of the rear-end housing from a 2-1/2 ton truck used as the swing unit. The rear-end section is welded solid to the trailer frame with 1/2" plate. 1/2" plate is welded to the top of the wheel and braced on the corners.

Front veiw of budd wheel w/1/2" plate. The axle and hub are visable here also. The plugs for the winch plug into a "bumper jumper" on the truck.

Snow plow cylinders swing the unit about 45 deg out from each side of the trailer. A 2 bolt flange bearing was used on the bottom part of the axle.

Front view of the whole unit. The bumper jack also serves as a stabilizer on the side I'm loading from. Disconnect couplers on the hyd hoses hook up to the power unit in the back of the truck.

This crane unit puts alot of weight on the trailer tongue. I wouldn't advise pulling this with a half-ton pickup. I have 1-ton leaf springs in my F250 and it handles it fine.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Business

  • KnowledgeBase: Forestry

  • KnowledgeBase: Forestry: Woodlot Management

  • KnowledgeBase: Primary Processing

  • KnowledgeBase: Primary Processing: Sawmilling

  • KnowledgeBase: Primary Processing: Woodlot Management

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article