<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>

 

 
   
   
 
 
 
 
 
 
 



How to Stop Inset Doors Flush with the Face Frame

      The search for a high-quality detail for stopping inset doors. March 22, 2013

Question
I'm looking for a nice solution to stop inset doors flush with the face frame. The job is a high end kitchen.

Forum Responses
(Cabinetmaking Forum)
From contributor K:
If you mean the job is custom and finely detailed, then the face frames will be rabbeted on four sides to prevent seeing into cabinets, just as fine furniture has been for centuries. Paired doors will be reverse rabbeted to permit a wide opening. The rabbets stop the door, and are a very nice solution. From there, a bullet catch used to be the preferred method. Today, better work now uses rare earth magnets hidden under shallow plugs.



From contributor M:
You can also use a Euro stop made by FastCap. They are door stops with an off center hole which allows you to adjust them.


From contributor S:
Häfele America Co. has a couple solutions including the screw-on stop and an adjustable magnetic catch. Check out #251.79.600 for the stop and 246.15.110 and 246.15.610 for the mag catch.


From contributor A:
Having tried a variety of solutions over the last decade, including shop-made wood stops with self-closing hinges, the Hafele stops posted above, and various other mechanical and magnetic, low-tec and hi-tec things, I've decided that everything other than a rabbeted face frame is a waste of time.


From contributor I:
Inset stops. We rip lineal oversize to finish 3/4 x 1.25. Run a rabbet cut on the shaper. Mill the piece to remove tear out and size. The rabbet depth set according to bumper thickness. Will cut stop piece the width of face frame opening and pin/glue on the back side of face frame. The rabbet width is 1/2" exposed and 3/4 is glue surface. This blends with the face frame. Might be overkill, but found it to be pretty fast and didn't have to come back with mechanical hardware after finish.


From contributor W:
The rabbet must be for euro hinge. What about butt hinge where magnet is needed?


From contributor N:
We use the magnetic stop that contributor S posted above for inset doors with butt hinges. They work very well and are adjustable. For inset doors with Euro hinges we make our own stops from wood.


From contributor H:
We only do inset, and the best thing I found over the years is a small clear plastic door stop from Outwater held in place with a 5/8'' x #6 screw.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?


Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction


    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.



    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    Woodweb.com
    865 Troxel Road
    Lansdale, PA 19446

    Contact Us











  • WOODWEB - the leading resource for professional woodworkers


      Home » Knowledge Base » Knowledge Base Article
     
    无限在线观看免费看视频