<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Optimal Size to Rough Cut for Flooring

      Start with a uniform finish thickness, then add allowances for planing, drying shrinkage, and cupping. October 26, 2011

I am currently cutting maple to be used as a 3/4 x 3 1/4 flooring. I am wondering what the optimal cutting thickness should be to allow for shrinkage. Also I am curious if the width should be cut to size before or after drying.

Forum Responses
From contributor M:
Most stock has been cut a little over an inch so that it shrinks to one inch after kiln drying. Cutting into strips will improve yield, but you will lose the ability to rip out a straight piece if it gets sidebent or twisted. You can crosscut the sidebend out but get a much shorter average length in the floor

From Gene Wengert, forum technical advisor:
With the flooring, you want every piece to be 0.75" and not just the average. You must then add a planer allowance, perhaps 3/32", or 0.09", but it might be more. Then add 8% or about 0 .07" for maple shrinkage (more for oak). You could add a few 0.01 for cup. This gives you the minimum thickness. In a good mill, add 0.08" to get the average or target thickness for the sawmill.

From contributor E:
I would start out with " thick wood 4"wide, run it through a kiln first then plane and cut to size and T&G it. Do not cut to width first as when the pieces dry, they will end up different widths.

From contributor H:
Curious as to what kind of equipment and amount of production you wish to accomplish. I should say depending on the equipment you have greatly effects how you will process flooring. I run 3.25?RO clear, select and 2.25?1Com which both can be ripped from the same size board. 8.75?X 1?is what I saw from a cant and AD for a while before the kiln. All my 3.25?is mainly new construction and 2.25?for remodels and additions to match existing flooring. With any species start with the finished product and work backwards, wider flooring you need to add a little extra width to get a straight as possible piece.

There is nothing like using a four ton frame straighter to install 7.25?white oak that is just a little bowed. Starting from your finished piece, add your allowances for tongue and groove, gang rip blades, and shrinkage. If you do not have a gang-rip or slr for making blanks I would saw 4?to 4.25?boards and make sure you get as much weight on them as possible and condition them. Nothing worse than spending six hours cross-cutting blanks to get semi-straight pieces.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Architectural Millwork

  • KnowledgeBase: Architectural Millwork: Flooring

  • KnowledgeBase: Primary Processing

  • KnowledgeBase: Primary Processing: Sawmilling

  • KnowledgeBase: Primary Processing: Yield Formulas

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article