<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Outfeed Table Plan

      Construction ideas for an outfeed table with mounted router. March 14, 2004

I'm finally biting the bullet and shutting down the shop for a few weeks to renovate. I need to build a new outfeed table with a spot for a router mounted underneath. Does anyone have plans, designs, or good ideas for a new table? We currently keep sheet goods under the one we have now. Size is to be at least 5'x12'.

Forum Responses
(Cabinetmaking Forum)
From contributor D:
I don't know what kind of saw you have or how much room you have, but consider putting your router in the extension to the right of the saw. I saw this done before and one of my helpers wants me to do it in the future. That way you can use the table saw fence with the router. It may come in handy for certain cuts.

From contributor J:
Quickest way I can think of is to use 2 4x8 sheets of MDF, one cut to depth of table saw to be placed to the left, one to be whole and turned to intersect so it lays in front of the saw.

Takes a few studs to build a quick leg setup, level the saw, shim the table, brace it and you're done.

If you want to store sheet goods under it, just 'T' the legs for strength and nail a 2x4 horizontally across to make a lumber rack, or set of lumber racks. They will need center supports, horizontal and lengthwise, to cut bowing to a minimum.

Although, with a 5x12 table, .75 material, and standard height around what... 34-36 inches, you'd be better off building a sheet rack behind the table 8 feet tall with 4-6 shelves, setting the table up with router, building a rack for bits and blades, putting shelves along the outside, storing a porty compressor or something underneath, etc.

From contributor R:
Don't put the router on your saw! You will always find that it is in the way, and your tablesaw is not a workbench. Build the table ext. for the saw - you do need this, and then build a nice bench for the router. There are many very good sets of plans out there.

From contributor W:
I have a jet with a 50" Bessy fence. I put a Jessem Router lift in some maple plywood in the extension to the right of the iron table. Works great and I made a sacrificial fence that fits over the top of my Biesemeyer fence so that I can cut raised panel doors. It works really nicely.

For the outfeed table, I made a 2.5' X 6' table that is on casters. I can attach it either width-wise or length-wise to the outfeed of the table. I use small c clamps to hold the outfeed table to the rear fence rail. I cut a couple grooves into the outfeed table for the miter gauge to slide into. The tablesaw keeps the outfeed table from moving around.

I like mine and use it as a worktable too, since it's big enough to cut most small projects without having to clean the top off for each cut.

From contributor S:
We have another saw for ripping solid woods and a slider for sheetgoods. This setup is for all other miscellaneous cutting and the router table. There are holes in saw fence and we screw the dust collector fence to it. There is a 2-1/2" hose that goes over the top and there is a 4" downdraft through box around router. Switch on router is in on position and is plugged into switched outlet below fence guide. I know the place is a wreck. Tomorrow it will be cleaned, I swear.

The whole set up is only 7'x 9'. If you only have one saw setup, I would agree with contributor R, and build it into something else. But this setup works great for us, since it's not our main saw.

The side of setup is used for shaper sled storage and blades.

From contributor R:
What a nice setup. Something to think about for the future.

I wish I could shut down for a couple of weeks. I save time on Saturdays to do refab work. Try to do one thing or another to improve setup times, work areas, etc. And sometimes just clean.

From contributor Y:
Here's my outfeed table plan.

From contributor M:
Please excuse my wonderful mess. My tabletop is 12ft by 8ft.

Contributor S, don't you find it to be a bit difficult to cut full sheets on that? Do you have a panel saw?

From contributor S:
We have 5 saws. One slider, one rip, one set up for back dadoes and these two for everything miscellaneous.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Business: Plant Management

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Furniture

  • KnowledgeBase: Solid Wood Machining

  • KnowledgeBase: Solid Wood Machining: General

  • KnowledgeBase: Solid Wood Machining: Setup and Maintenance

  • KnowledgeBase: Woodworking Miscellaneous

  • KnowledgeBase: Woodworking Miscellaneous: Accessories

  • KnowledgeBase: Woodworking Miscellaneous: Woodworking

  • KnowledgeBase: Cabinetmaking: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article