<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Quality and Cost for Veneered Cabinet Faces

      The cost of veneered panels varies depending on the required appearance and the level of craftsmanship. May 31, 2014

Question (WOODWEB Member) :
Crystal Cabinet Works up in sunny MN makes a couple lines of contemporary fronts, all doors and drawer fronts flush. Photos for the look are below. There are two offerings. One with taped edges, tape matches faces. The other is with 1/8" solid edges, species matches faces. Of course the one with solid edges carries a higher price.

Unfinished doors in, say, a rift-sawn white oak look might carry a material cost of what? The MDF core, edges, veneers, adhesive, all might come to $12 per square foot? Am I close? The solid edge version is going to carry a little more cost, of course. Not much more, we're talking material costs here. But let's say a shop is set up with equipment to make either. Which door then gets the higher labor cost, including burden costs for machine time, etc.?

Click here for higher quality, full size image

Click here for higher quality, full size image

Click here for higher quality, full size image

Forum Responses
(Cabinetmaking Forum)
From Contributor C

Click to View Member Profile Member Contact Info Categories

My short answer is it depends. The stuff in your picture is mismatched - basically cut sheets. If you shop well you can get five piece doors at a good cost. To do a proper matched veneer kitchen, there is a lot of labor in laying out the veneer faces so they match vertically and side to side with full veneer plates (leaves) side to side. Each panel needs to be made separate and cut carefully to align with adjacent panels, the veneer leaf with will vary for each panel slightly for a true balanced effect on each panel and overall. The effect can be dramatic. However that is not what your pictures indicate, the veneer may be reconstituted also, but it's mismatched for the most part. The banding difference is minimal. We use an in house made 2-ply veneer from the same log as the project which is about .050" before sanding. Some request 3mm (1/8) material with 2.5mm radius.

We are not in the kitchen business but we do contract veneer work for a bunch of companies. I am continually amazed how much time it takes to do this correctly for large kitchens. By the same token, smaller straight forward kitchens come in quite reasonable. Attached is a pic of a small local job we did.

Click here for higher quality, full size image

Click here for higher quality, full size image

Click here for higher quality, full size image

From Contributor F:
I agree that there are different ends to the spectrum with how you can go about this. The easiest panel to make is a veneered MDF panel that you band the edges. In most cases if done properly the edges will look seamless to all but the most experienced eyes. However to avoid the mis-matches shown in your second pic requires a bit of time and planning. It also needs to be done with someone with enough experience that they can keep the alignment together across the whole job to avoid those mismatches.

Actually banding the panel first and then veneering is much more time consuming and much more expensive for materials. I don't do much of that except for the rarest of jobs where the price can be justified. Now if you’re trying to narrow it down to just the difference between a solid band and a taped edge leaving out the rest of the construction, I don't think there's going to be much difference at all outside of the material costs as long as your still buying the solid banding and applying it with an edge bander. Where would the extra labor costs come from?

From contributor Y:
Strip feeding and sawing/sanding solid edges takes more time. Using multi-layer veneer coil banding is much faster at the bander. The lumber to make strip banding isn't much, but the sawing and sanding time could easily add an hour or probably more to the cost of a kitchen. The photo of the kitchen with slip match veneer and panel to panel architectural match is much better looking. Will your customer pay for it? Do they care?

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Business

  • KnowledgeBase: Business: Estimating/Accounting/Profitability

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

  • KnowledgeBase: Veneer

  • KnowledgeBase: Veneer: Techniques

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article