<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Reducing Shaper RPMs

      Advice on stepping down a shaper's drive motor to accommodate a sanding wheel. March 27, 2012

Does anyone know how I can reduce the rpmís on a shaper/machine? I want to put a profile sanding head on a shaper, but need to reduce the RPMís. Iíve heard about inverters but donít know a lot about them.

Forum Responses
(Cabinetmaking Forum)
From contributor H:
Change the pulleys. Any bearing house will be able to compute the diameters to get the RPMís you need.

From the original questioner:
I canít change pulley on the spindle. There is not enough space for a bigger driven pulley. Could I change the pulley on the motor? The motor RPMís are 3600.

From contributor U:
If it is 3ph you could use the vf drive if you do not need to slow the motor down too much as this would heat the motor up. How much RPM reduction do you need?

From contributor G:
Looking around at spindle sanders it looks like you need to get to around 1750 RPMís. Most shapers lower speed is around 7000 RPMís. A large shaper might go down to 4K RPM. That's a long way to go. If it is a 3PH machine, like Contributor U suggested, a VFD will do the trick as long as you don't plan on making it a dedicated machine that will be used hours at a time.

From contributor Y:
Sit down before you look at the price of VFD's! Also, some motors will not be able to dissipate enough heat when running slower. They make motors that are specifically rated for VFD's.

From contributor W:
Swap motors. A 3600 rpm motor is unusual. Most are 1750. Another possibility would be to add a third pulley to the system. This very much depends on the clearances inside the cabinet.

In a nutshell: Replace the pulley on the motor with a step pulley. Run another step pulley on an independent shaft. That shaft has a second pulley that drives the spindle pulley. If the openings are in the wrong place, you may need to put the independent shaft where the motor is, and move the motor.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Solid Wood Machining

  • KnowledgeBase: Solid Wood Machining: Setup and Maintenance

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article