<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Shared Power Switch for Tool and Vacuum

      Quick tips on linking tool and shop-vacuum power supplies so that the vacuum starts when the tool starts. April 24, 2013

Does anyone know of a switch that is available to be used like the Festool type which turns on the vacuum when the tool you are using is turned on? I have a Festool vacuum now but would like to incorporate other shop vacuums for out on installations.

Forum Responses
(Cabinetmaking Forum)
From contributor C:
I bought some at Sears, of all places. You plug the tool and the vac into the switch and the switch into a receptacle. I have one on my band saw so when I turn the band saw on, a light comes on and I have one on my ro so when I turn the ro on, a vac comes on. It also lets the vac run for a few seconds after I turn the ro off. I think they were only like 30.00.

From contributor L:

From the original questioner:
Thanks! I ordered 2 of them from Amazon this morning. I know I can always count on you guys on WOODWEB for answers to everyday problems.

From contributor G:
I like Lee Valley's automatic vacuum switch. They allow you to use separate plugs for the tool and the vacuum to prevent popping the breaker. If you are using a 3 hp router and a good sized vacuum this becomes a necessity.

From contributor N:
Contributor L, just wondering what kind of vac you use for your Mirka ceros. I have a regular shop vac plugged into an auto switch but the vac will only run if the sander is on one of the two higher rpm settings. It will not turn the vac on using the low rpm settings. I might buy an isocket to see if it would work.

From contributor L:
I have the Fein 9-20-25 Turbo-II 9-gallon wet/dry vacuum. It has an auto switch built in.

From contributor N:
Will that vac turn on when the Mirka Ceros is turned on in low rpm's? I use a dust deputy hooked to my vac. It keeps 90% of the dust out of the vac filter.

From contributor L:
Yes, the lowest rpm will activate it. I had a problem with the iSocket and lower speeds, but not the Fein vac.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: General

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article