<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Sliding Table Saw Crosscut Fence Safety

      The crosscut fence on a slider is positioned for managing large panel cuts. April 10, 2008

I would like to know why it is that these higher end sliding table saw machines have the cross cut fence to the top of the sliding table instead of at the bottom or close to the operator. I realize this is for cutting large panels, but currently I work in a shop where this "free hand cutting" or the stock being pressed into the fence instead of in front of the fence is considered normal. I consider this dangerous. Can anyone comment on whether this is proper procedure and why it conflicts with what I have been taught and instructed over the years?

Forum Responses
(Dust Collection Forum)
From contributor W:
I think you have the key idea, which is that it is for large panel cutting. It is much easier to push a piece against the reference fence and stops in the forward configuration. The tendency to come away from the fence is counteracted on most saws by a positionable bar that goes behind your thigh, giving you purchase to apply constant pressure forward.

From contributor L:
The shop is doing it right. With large panels you need to be able to hold up the back outside corner of the panel. Using the correct feed speed and hand positions will allow safe large panel cutting. As the panel gets smaller and lighter you will need to use one hand pushing the panel against the front fence and one hand on the sliding table to maintain a counter pressure on the sliding table. It works well and is safe. Sometimes an inexperienced operator will use too fast of a feed speed and cause the panel to move back away from the front fence, immediately binding the panel on the blade and hopefully learning the right technique.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

  • KnowledgeBase: Panel Processing

  • KnowledgeBase: Panel Processing: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article