<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



Space Efficient Dust Collector Ideas

      Ways to shoehorn dust collection into tight quarters. February 26, 2007

I just purchased a small edgebander and need a dust collector for the trimming but don't have much space (unfortunately, it is far away from my saw's dust collector and that one is pretty poor to begin with).

Can anyone suggest one that is relatively small but does a good job? I can afford to have a small collection bag because I will not be generating a lot of waste. I assume a cartridge type unit is smaller than a bag.

Forum Responses
(Cabinetmaking Forum)
From contributor L:
Do you own a Shop-Vac? Fit that thing onto the dust port. I understand it also vacuums.

From contributor B:
I have a Penn State Industries collector dedicated to my bander. They make a number of smaller machines. I have mine mounted to the wall to save space. I wouldn’t bother with a cartridge if I were doing it again.

From contributor P:
I would suggest checking out Oneida's smaller units. I just shoehorned a 5 hp. cyclone into a tiny space, and I’m delighted with the results. They also offer great service and support. I think they've come out with a smallish roll-around unit as well.

From contributor T:
You can really ramp up the output of any dust collector by swapping out the fabric bags that come with them for custom made felt bags.

We have a half-dozen 2 hp dust collectors that pull dust an amazing distance with these bags. Our 20 inch jointer evacuates close to 40 feet to a mezzanine 8 feet above the jointer. These small machines are quiet and don't use as much electricity. It all happens because of the bag.

From the original questioner:
I will do some research as suggested.

Contributor T - I did change to a felt bag on my 2 hp and it made a tremendous difference. What I am now thinking of doing is piping up the bander to my existing dust collector and seeing if it does the trick. If not, just get a better collector for the whole shop (my old one has paid for itself many times over). This is probably the most space efficient in that I will only need one unit for everything.

From contributor H:
I have a 2 hp Grizzly with felt bags between my slider and bander (approximately 10 ft from the saw and 15 ft from the bander. I have a Cehisa EP-9 and it does a great job of dust collection for both machines.

From contributor B:
Below is a Jet collector on top of our bander and it works great.

Click here for full size image

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article