<video id="75bvl"><noframes id="75bvl">
<listing id="75bvl"><thead id="75bvl"><listing id="75bvl"></listing></thead></listing>
<listing id="75bvl"></listing>
<listing id="75bvl"><cite id="75bvl"></cite></listing>
<var id="75bvl"><ruby id="75bvl"><th id="75bvl"></th></ruby></var><th id="75bvl"><th id="75bvl"></th></th><noframes id="75bvl">
<listing id="75bvl"></listing>
<span id="75bvl"><strike id="75bvl"><dl id="75bvl"></dl></strike></span>



When to Change Finishing Booth Air Filters

      You can go by air pressure or by airflow, but the limits vary depending on location. November 26, 2006

We have in our finishing department open ended finishing booths. Can anyone tell me what the reading on the manometer should be when it is time to change the filters?

Forum Responses
(Finishing Forum)
From contributor H:
I think that it should be about .5, but my booth is very old and there is not any fluid in the doohickey. I change the filters when the spray starts to hang up in the ceiling of the booth.

From contributor R:
1. After installing a new filter, turn on the fan and mark the manometer at the pressure level that is indicated.
2. Check the manometer every time the fan is turned on.
3. If the pressure reading on the manometer increases by 0.25 in. wg (inches of water gauge), then it is time to change the filter.

From contributor T:
Contributor R is right, but if you do not live in an air quality district that has the .25 rule, you can change when your average velocity has dropped below 100 lineal CFM per minute (the OSHA requirement for spray booths). Since most booths are rated to overcome .5" of static pressure, they will lose the minimum of 100' feet per minute at .5" of static. Therefore, a good rule of thumb is to change your filters at .5" of static pressure difference unless you live in a regulated area that requires the .25 rule.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Dust Collection, Safety, Plant Management

  • KnowledgeBase: Dust Collection, Safety, Plant Management: General

  • KnowledgeBase: Finishing

  • KnowledgeBase: Finishing: General Wood Finishing

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - Woodweb.com
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review Woodweb.com's Copyright Policy.

    The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

    865 Troxel Road
    Lansdale, PA 19446

    Contact Us

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article